車輪裝備 車輪模具 汽車模具 汽車零部件

刨滾切機組

本設備由刨渣機、滾壓機、端切機三部分組成,其中,刨渣機是車輪生產中的專用設備,用于除去輪輞焊接后產生的焊渣,從而得到平整的焊縫表面。焊縫滾壓機用以壓平并強化刨渣后的焊縫,經過滾壓后焊縫和母材平齊。端切機用于切除焊縫兩端頭多余的焊接材料,沖切動作由油缸驅動

詳細描述

概述

Summary

本設備由刨渣機、滾壓機、端切機三部分組成,其中,刨渣機是車輪生產中的專用設備,用于除去輪輞焊接后產生的焊渣,從而得到平整的焊縫表面。焊縫滾壓機用以壓平并強化刨渣后的焊縫,經過滾壓后焊縫和母材平齊。端切機用于切除焊縫兩端頭多余的焊接材料,沖切動作由油缸驅動。

This machine is composed of trimmer, planisher and end cutting unit, which of trimmer is special equipment of steel wheel production for removing and trimming welding slag generated by wheel rim welding to obtain flat welding seam surface. Planisher machine is used to flatten and strengthen the welded seam after welding slag planishing and trimming. End cutting machine is used for cutting the both ends of redundant welding materials of welding seam, cutting action drives by oil cylinder.


規格參數

Specification

參數描述/Description Data

設備型號model numberBGQ-300-AH
額定輸入電壓rated input voltageAC380V,3Phsae
額定輸入頻率rated input frequency50Hz
額定輸入容量rated input capacity37KVA
工件厚度Max. thickness of rim5mm
工件寬度范圍width range of rim220-320mm
工件直徑范圍diameter range of rimφ280~φ450mm
刨渣夾緊力maximum clamping force of trimmer6Tons
刨渣力maximum trimming force6Tons
滾壓夾緊力maximum clamping force of planisher6Tons
滾壓滾壓力maximum rolling force of planisher6Tons
端切剪切力maximum cutting force of end-cutting18Tons
端切剪切油缸直徑diameter of cutting oil cylinder of end-cutting160mm
系統壓力system pressure12Mpa


刨渣單元

Trimmer Unit

刨渣機是車輪生產中用于除去輪輞焊接后產生的焊渣,從而得到平整的焊縫表面。該機設計為自動操作,由主機、液壓系統和電氣系統等組成.其中液壓系統和電氣系統與滾壓機、端切機共用。

Planning machine is special equipment of steel wheel production for removing and trimming welding slag generated by wheel rim welding so as to obtain flat welding seam surface. The machine is designed as automatically operation, it consists of host, hydraulic system and electric system, wherein hydraulic system and electric system are shared with rolling press machine and end cutting machine.

床身/Lathe Bed

主機架為C-型機構,液壓驅動夾持器在焊縫兩側壓緊。

Host frame is C-type mechanism. The hydraulic driven clamp holder clamps two sides of welding seam.

夾緊機構/Clamping Mechanism

工件由液壓夾緊機構夾緊固定,該機構安裝于導軌上方, 為阻止工件在刨渣時軸向松動、在夾緊鉗口上裝有止動塊。

Work piece is clamped and fixed by hydraulic clamping mechanism, and the mechanism is installed on the upward side of guide rail. The stop block is installed on clamping jaw to avoid axial loosening of work piece during slag planning.

夾緊機構分上下兩部,下部固定在機架床身,上部分為運動部分,由油缸驅動。

The clamping mechanism is divided into two parts, the lower part of which is fixed on the lathe bed of frame, the upper part is movable and driven by oil cylinder.

刨渣機構/ Trimming Mechanism

上下刨渣刀安裝于鋼制滑架上,此滑架由硬化處理的導軌支撐在夾持器中間來回運行,每個刀片的切割面根據材料厚度手動設定。

Upper and lower slag planning cutter is installed on steel sliding frame. The sliding frame makes to-and-fro movement in the middle of clamp holder by support of guide rail after hardening treatment, and cutting surface of each cutter is set manually according to material thickness.

刨渣刀具的切割面和夾持器采用一套機械機構相連,以保證其相對位置,這樣無論何種厚度的材料,機器將不必每次設定,可自動適應切割不同厚度的材料。

Cutting surface and clamp holder of slag planning cutter are connected by one set of mechanic mechanism to ensure its relative position. Therefore, whatever any material thickness, the machine will not set each time, and can cut material with difference thickness automatically.

滑架上裝有三組刀具,下夾持器為固定式,同時也作為下滑架導軌。上下刀具運動由液壓缸驅動。

Three cutters are installed on sliding frame, and lower clamp holder uses fixed-type, and is also used as guide rail of lower sliding frame. Movement of upper and lower cutters is driven by hydraulic cylinder.

夾緊機構/Clamping Mechanism

工件由液壓夾緊機構夾緊固定,該機構安裝于導軌上方, 為阻止工件在刨渣時軸向松動、在夾緊鉗口上裝有止動塊。

Work piece is clamped and fixed by hydraulic clamping mechanism, and the mechanism is installed on the upward side of guide rail. The stop block is installed on clamping jaw to avoid axial loosening of work piece during slag planning.

夾緊機構分上下兩部,下部固定在機架床身,上部分為運動部分,由油缸驅動。

The clamping mechanism is divided into two parts, the lower part of which is fixed on the lathe bed of frame, the upper part is movable and driven by oil cylinder.

刨渣機構/ Trimming Mechanism

上下刨渣刀安裝于鋼制滑架上,此滑架由硬化處理的導軌支撐在夾持器中間來回運行,每個刀片的切割面根據材料厚度手動設定。

Upper and lower slag planning cutter is installed on steel sliding frame. The sliding frame makes to-and-fro movement in the middle of clamp holder by support of guide rail after hardening treatment, and cutting surface of each cutter is set manually according to material thickness.

刨渣刀具的切割面和夾持器采用一套機械機構相連,以保證其相對位置,這樣無論何種厚度的材料,機器將不必每次設定,可自動適應切割不同厚度的材料。

Cutting surface and clamp holder of slag planning cutter are connected by one set of mechanic mechanism to ensure its relative position. Therefore, whatever any material thickness, the machine will not set each time, and can cut material with difference thickness automatically.

滑架上裝有三組刀具,下夾持器為固定式,同時也作為下滑架導軌。上下刀具運動由液壓缸驅動。

Three cutters are installed on sliding frame, and lower clamp holder uses fixed-type, and is also used as guide rail of lower sliding frame. Movement of upper and lower cutters is driven by hydraulic cylinder.


滾壓單元

Planisher Unit

滾壓焊縫機用以壓平并強化刨渣后的焊縫,經過滾壓后焊縫和母材平齊。滾壓焊縫機的主要部件為:床身、可運動的C形框架、夾緊機構、滾輪及液壓件。C形框架,裝有液壓驅動用以滾壓固定于夾緊機構的制件的滾輪。

The planishing machine is use to flatten and strengthen the trimmed welding-seam, the planisher's main parts includes machine, movable C-type frame, clamping device, rollers and hydraulic parts. C-type frame equipped with hydraulic drive system for rolling roller that fixed on the clamping mechanism.

C形框架/ C-type Frame

C形框架固定于可沿導軌運動的支架上,油缸驅動,支架通過每邊四個滾柱軸承滑動,C框架的主要功能是阻止滾壓力的偏移及由此導致的滾壓尺寸的偏移。

C-type frame fixed on the holder that can move along with the guide rail, it will be driven by oil cylinder. Holder can slide through roller bearing that set four (4) roller bearings each side. C-type frame's main function is to prevent rolling pressure skewing and the resulting rolling press size deviation.



 端切單元

 End Cutting Unit

床身/ Lathe Bed

C框架支持所有主要部件而且便于操作和調整。油缸固定在框架頂部用以驅動夾緊和沖切機構,可根據制件寬度調整的手輪調節機構裝于框架尾部。

C-type frame supports all major components and it is convenient for operation and adjustment.

Oil cylinder fixed on the top of the C-type frame which is used to drive the clamping and cutting mechanism, and it can be adjusted according to the width of rim band, the hand wheel adjusting mechanism mounted on the tail of frame.

沖切機構/Cutting Mechanism

沖切機構通過切邊模切除焊縫兩端頭。高壓油缸(行程60mm)驅動上模,上下模間導柱一線性導套相連,上模固定于上模座,下模為下模座的一部分。前部刀具(上、下)固定于上下模座,后部刀具裝于可動滑座上(可隨制件寬度調節)。

Cutting mechanism cuts the both end of welding slag by cutting tool. The upper tool drives by high-pressure oil cylinder that stroke is 60 mm, upper tool (cutter) and lower tool (cutter) connects together by the linear guide pillar and guide sleeve. The front of the cutting tool (upper and lower) fixed on the upper and lower tool base, the back of the cutting tools installed on the movable slide base which can be adjusted according to workpiece width.

切邊刀具由工具鋼制作,每對刀具分別為凸、凹形狀以逐步完成材料切邊。上下刀具間隙應為料厚的8-10%,這樣才能達到0.2mm的標準零件尺寸,間隙應該在刀具調節完畢后進行檢查!

Cutting tools (cutter) made by tool steel, each pair cutter includes convex and concave shape tool, complete material cutting quickly. The clearance of upper and lower cutting tool should be 8-10% of the material thickness, for achieving the standard workpiece size at 0.2 mm.

NOTE: The clearance should be checked after cutting tool adjusting finished!

手輪調節機構/ Hand wheel Adjuster

手輪調節機構通過調節滑座位置以適應零件寬度的變化,包括氣缸、尾座及其上的切邊刀具,滑座可以通過框架后面的手輪而水平移動。

Hand wheel adjuster can adjust the sliding seat position to adapt the width change of work pieces, including air cylinder, the tailstock and cutting tools, sliding seat can move horizontally by the hand wheel at the back of frame.


冷卻單元 

 Cooling Unit

氣壓驅動,杠桿結構。上下冷卻銅板內通循環冷卻水。

The cooling unit is driven by the air pressure and designed as lever structure. Inside upper and lower cooling cooper band has cooling water circulation.


魯ICP備090054547號-1 | © 2018 山東小鴨精工機械有限公司 版權所有


掃一掃 了解更多

郵編:250000

地址:山東省濟南市工業南路51號

營銷事業部:+0531-83122188

郵箱:[email protected]

400-6586-222轉8

在線營銷
live chat
369网络棋牌 福利彩票双色球开奖时间 pk10免费计划软件手机 天津时时直播 排位表资料 广东快乐十分钟开奖直播 江苏时时诈骗 手机上安徽麻将 内蒙古快三热点早知道 一肖一码期期准1一3码 赛车pk10教技巧